| Customization: | Available |
|---|---|
| Application: | Construction |
| Bonding Strength: | / |
|
Still deciding? Get samples of US$ 0/Bag
Request Sample
|
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
| Chemical Nature | Polypropylene Mesh Fiber(PPSF) is made of propylene as raw material through special processing. Its appearance is a network structure formed by the interconnection of multiple fiber monofilaments. When the PPSF is put into concrete during the mixing process, the transverse connection among the fiber monofilaments will be destroyed by the concrete's rubbing and friction to form a fiber monofilament or a network structure that is fully opened. This is because it achieves the anti-cracking effect of many polypropylene fiber monofilaments.  |
||||||||||||||||||
| Typical Properties |
|
||||||||||||||||||
| Features of application | The performance improvement advantages of PPSF are convenient for almost any engineering fiber concrete. Therefore, combined with the characteristics of China, the most practical engineering uses of PPSF are selected as follows: ★concrete pavement, bridge deck, airport pavement, factory floor, and other projects. To prolong the project's service life (it can extend the extraordinary life of the road surface by 5-10 years). ★The walls and roofs of tunnels and mines. When spraying technology is used for concrete construction, the addition of PPSF will also effectively reduce the rebound rate of poured concrete so that the rebound of concrete will not exceed 5%, improve construction efficiency and improve the working environment and conducive to the promotion of wet spray technology. ★Rivers, dams, storage tanks, and other projects. The improvement effect of PPSF on concrete crack resistance, impact resistance, and wear resistance will prolong the project's service life. ★Milit ary protection engineering, wharf revetment, bridge piers, etc. PPSF dramatically improves the impact resistance of concrete, which will enhance the safety and prolong the service life of such projects. |
||||||||||||||||||
| Usage | Instructions ★Structural design Although adding PPSF can significantly improve concrete performance, in general, PPSF is still used as the "secondary reinforcement" of concrete to prevent shrinkage and crack concrete and prolong the service life, rather than the "primary reinforcement" to bear the main load. Furthermore, a large number of experiments have also confirmed that although the number of fiber monofilaments obtained after the dispersion of PPSF is large, the volume ratio of 0.9kg-1.8kg of it per cubic meter is only 0.1%-0.2%, so it has no noticeable effect on the parameters such as compressive strength and elastic modulus of concrete. Therefore, it should not change the reinforcement ratio of the main stress bars in the original design after mixing concrete with polypropylene mesh fibers. ★Length selection PPSF in general engineering should be 19mm long. ★Proportion design Typically, the dosage of PPSF in unilateral concrete is 0.9kg, and the dosage of the protective layer of the waterproof layer of the bridge deck is 1.8kg. It is not necessary to change the dosage of other materials. When there is a particular purpose, it can determine the amount of PPSF and the concrete mix ratio through experiments. For the concrete mixed with silica fume, finely ground slag, zeolite powder, and other active mixed materials, the use effect of PPSF is better. ★Mixer selection Need to use a forced mixer. ★Feeding process Put in crushed stone, fiber, and sand in order and stir for two minutes to open the fiber fully, then put in cement and water and mix evenly. The construction can also be carried out according to the input sequence of the conventional process, but the stirring time should be extended appropriately to make the fibers disperse evenly. ★Stirring time The purpose of stirring is to fully disperse the fiber network into monofilament or open the network structure. Under normal circumstances, it is enough to force the stirring for 2-3 minutes after putting in the concrete with polypropylene mesh fiber. ★Molding process There is no special requirement, but the concrete should be thoroughly vibrated. ★Conservation process There is no special requirement, and it can be carried out according to the standard concrete maintenance process. However, it can not relax the early maintenance of concrete due to incorporating PPSF. ★Durability PPSF Any organic material will gradually age under the comprehensive action of heat, light, oxygen, and other factors and lose its excellent performance. However, there is no such phenomenon when using PPSF because the fibers are entirely protected in the concrete. |
||||||||||||||||||
| Packaging | Packing is 1.0kg/hank and can also be packed according to the customer's requirements. |
||||||||||||||||||
| Storage condition | Keep away from heat or ignition sources. Don't store near strong oxidising agent (halogen, peroxide, etc) |
||||||||||||||||||
| Product safety | According to the legal provisions on dangerous goods and preparations, this product is non-hazardous. Not harmful to health or environment under normal use of product. If material is heated up, may cause burns. |
||||||||||||||||||
| General | The usual safety precautions when handling chemicals must be observed. These include the measures described in Federal, State and Local health and safety regulations, thorough ventilation of the workplace, good skin care and wearing of protective goggles. |
||||||||||||||||||
| Material Safety Data Sheet | All safety information is provided in the Material Safety Data Sheet for Polypropylene Fiber |
||||||||||||||||||
| Transport Regulation | Not known as a dangerous good according to transport regulations. |
||||||||||||||||||
){kind=link}